Onn 2.0 Channel Soundbar User Guide – Manuals

onn 2.0 Channel Soundbar User Guide

user manual inserts for fcc id

1. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
2. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. however, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
   • reorient or relocate the receiving antenna.
   • Increase the separation between the equipment and receiver.
   • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
   • Consult the dealer or an experienced radio/tv technician for help.
   1. This device may not cause harmful interference, and
   2. this device must accept any interference received, including interference that may cause undesired operation.

   package content

   1. sound bar 1pc
   2. 3.5mm to rca audio cable (length: 1.5m) 1pc
   3. remote control 1pc
   4. product guide 1pc
   5. external adapter 1pc

   

   speaker overview

   1. status indicator
   2. wall mount
   3. auxiliary input
   4. optical
   5. power
   6. power on / off
   7. source
   8. volume down
   9. volume up

   

   status indicator

   waiting

   solid red

   optics

   solid green

   auxiliary input

   solid white

   bluetooth pairing mode

   flashing blue

   connected bluetooth device

   solid blue

   volume up and down

   corresponding to the sound source indicator light flashes 1 time

   maximum and minimum volume

   corresponding to the sound source indicator light flashes 3 times

   silence

   slow flashing

   TV mode

   corresponding to the sound source indicator light flashes 2 times

   music mode

   corresponding to the sound source indicator light flashes 2 times

   movie mode

   corresponding to the sound source indicator light flashes 2 times

   specifications

   • output power: 12.5w x 2 (rms)
   • frequency response: 50hz~20khz
   • s/n ratio: ≥65db
   • separation: ≥45db

   remote control

   

   1. power on off
   2. mute
   3. bluetooth
   4. aux
   5. optical
   6. tv mode
   7. music mode
   8. movie mode
   9. volume up
   10. previous track
   11. play / pause
   12. next track
   13. volume down

   remote control batteries

   Before first use To prepare the remote control for first use, pull out the safety strip to activate the battery.

   Replacing the battery When replacing the battery in the remote control, refer to the diagram below.

   1. press the latch.
   2. while holding the latch, open the battery door.
   3. insert the battery noting the layout as shown. when replacing the battery, use only the same cr2025 type as specified.

   

   power and connection

   1. Connect the DC cable of the AC adapter to the power jack on the rear panel, and plug the AC adapter into the wall outlet.
   2. Press to turn on/off.
   3. Connect the audio cable to the audio output of any device (such as desktop pc, laptop, smartphone tablet, mp3, tv, etc.) with a 3.5mm headphone output jack or an rca output connector.

   bluetooth® connection

   1. turn on the sound bar and select bluetooth® mode.
   2. turn on bluetooth® on your device and search for nearby devices.
   3. search for “onn 16 ” soundbar” in the search results and tap to connect.
   4. the bluetooth® indicator will turn solid blue when the connection is successful.

   note:

   • the bluetooth indicator will continue to flash when the soundbar is pairing.
   • make sure there are no other active bluetooth® devices in range and the soundbar is within range. less than 3ft / 1m away from your device.
   • Before you start playing via bluetooth, turn down the volume to a moderate level.

   onn 2.0 channel soundbar user guide – download [optimized] onn 2.0 channel soundbar user guide – download